📞 +91-8538070869✉ info@arukalinstruments.in
Sales & service: West Bengal • Guwahati, Assam
Home / Products / Mixed Bed Plant
Cation resinamber beadsAnion resinblue beadsDM / RO water inUltra-pure waterBoth resins in one vessel: ions are removed again and again
Where the mixed bed plant sitsRawwaterRO orDM plantMixed bedpolisherArukalUltra-purewaterPolishes DM or RO water to the highest purity
Mixed bed capacity (m³/h)1MB 1laboratory5MB 5pharma10MB 10process25MB 25powerm³/hUsed as a polisher after DM or RO

Swipe a diagram sideways to see all of it

Plants and systems

Mixed Bed Plant

Polishing units for ultra-pure, very low conductivity water

Ultra purePolisherPharmaPower

Mixed cation and anion resin for the highest purity after DM or RO. Select, supply and support from Arukal Instruments, serving India and Nepal.

< 0.2 µS/cmOutlet conductivity
< 0.02 mg/LSilica
0.5 – 50 m³/hCapacity
Cation + anion mixedResin
Overview

What it does

A mixed bed unit holds cation and anion resin mixed together in one vessel. Each water molecule meets many cation and anion exchange sites, so the water leaves with extremely low conductivity, far lower than a two bed plant can reach.

It is normally used as a polisher after a DM plant or RO. Arukal supplies mixed bed plants with vessels, internals, mixed resin, regeneration tanks and controls, and supports resin replacement.

Where the mixed bed plant sitsRawwaterRO orDM plantMixed bedpolisherArukalUltra-purewaterPolishes DM or RO water to the highest purity
1

Service

Water flows through the mixed resin. Cation and anion sites remove the last ions.

2

Exhaustion

When the resin is exhausted, conductivity at the outlet starts to rise.

3

Separate

Backwash separates the lighter anion resin from the heavier cation resin.

4

Regenerate and remix

Alkali and acid regenerate the two resins; air mixes them again.

Features & benefits

Why choose Arukal mixed bed plants

Highest purity

Outlet conductivity below 0.2 µS/cm is typical.

Very low silica

Silica below 0.02 mg/L for boiler and high-pressure steam.

Polishing duty

Works after DM or RO for stable high-purity water.

Compact

One vessel instead of two.

Automatic or manual

Valve-operated or PLC-controlled regeneration.

Resin and support

Mixed bed resin and servicing from Arukal.

Technical data

Specifications

Typical values. Values are typical for the product family and given for guidance. Exact figures depend on the make and model supplied; ask us for the data sheet of the specific model.

Plant (typical)

ProcessStrong acid cation + strong base anion mixed bed
Capacity0.5 – 50 m³/h
Outlet conductivity< 0.2 µS/cm (typical)
Outlet silica< 0.02 mg/L (typical)
Service flow rateup to 40 m/h
Feed qualityConductivity below 20 µS/cm (after DM or RO)

Construction

VesselFRP or MS rubber lined
ResinCation : anion typically 1 : 1.5 by volume
RegenerantsHCl or Hâ‚‚SOâ‚„; NaOH
ControlsManual, semi-automatic or PLC with conductivity monitoring
Models

Typical plant sizes

ModelCapacityVesselTypical use
MB 11 m³/h13 – 18 inLaboratory, small boiler
MB 55 m³/h24 – 30 inPharma, electronics
MB 1010 m³/h36 inPower and process
MB 2525 m³/h48 inPower plants

Capacity per cycle depends on feed conductivity. Ask us for a design.

Mixed bed capacity (m³/h)1MB 1laboratory5MB 5pharma10MB 10process25MB 25powerm³/hUsed as a polisher after DM or RO
Selection guide

What we need to design your mixed bed plant

  • Feed water type (DM, RO permeate) and its conductivity and silica
  • Required outlet conductivity and silica
  • Flow rate (m³/h) and hours of operation
  • Acid and alkali available at site
Choosing by purityBelow 20µS/cmtwo bed DMDM plantBelow 1µS/cmhigh-pressureboilerDM + mixedbedBelow 0.2µS/cmpharma, powerRO + mixedbedUltra pureelectronicsRO + EDI +mixed bedSend us your feed analysis for a firm recommendation
Applications

Where it is used

Power plants and high-pressure boilers
Pharma and biotech
Electronics and semiconductor
Laboratories
Battery and chemical plants
RO polishing
Handling & care

Installation, use and care

  1. 1

    Keep the feed clean

    Run the mixed bed after DM or RO so it is not overloaded.

  2. 2

    Regenerate

    Regenerate on conductivity rise. Separation and remixing must be complete.

  3. 3

    Monitor

    Use an online conductivity meter at the outlet.

  4. 4

    Replace resin

    Replace resin when capacity and quality fall.

Downloads

Data sheet and brochure

FAQ

Frequently asked questions

Why use mixed bed after DM?

A two bed plant leaves traces of ions. A mixed bed removes them and gives much lower conductivity.

Can mixed bed treat raw water?

No. It would exhaust quickly. Use it as a polisher.

How is the resin regenerated?

The two resins are separated by backwash, each regenerated, then mixed with air.

How long does the resin last?

Often several years. Keep iron and chlorine out of the feed.

Do you supply mixed bed resin?

Yes. See Ion Exchange Resin.

Related products

Supplied across India — enquire from Guwahati, Assam & North-East, West Bengal or anywhere in India and Nepal.

Need help choosing the right water treatment solution?

Request a Quote →